- Chrysler drb iii bench test pdf#
- Chrysler drb iii bench test driver#
- Chrysler drb iii bench test full#
- Chrysler drb iii bench test software#
SC OVERRRIDE: CCD xmit: A4-00-FF sc: MIC 0x80004d26 OIL PRESSURE: CCD xmit: 0C-00-FF sc: MIC 0x80004d23 OD LOCKOUT LAMP RQ: CCD xmit: A4-00-FF sc: MIC 0x80004d1d LOCK DOORS: CCD xmit: A4-00-FF sc: MIC 0x80004d1c Also the fuel mileage is very poor, too (9-12 liters/100 km). This is most likely true because the key method returned with the 21 MIL code which indicates an Oxygen sensor fault. The fault name is O2 SENSOR 1/1 HIGH and the description is Oxygen sensor 1/1 input voltage maintained above normal operating range / shorted to voltage. There are older documentations that match the above pdf:
Chrysler drb iii bench test pdf#
PDF on the internet that contains error codes not only in the traditional OBD-II format but in HEX format too. You can downloat it below: = 0x4C = CRC-8, also good thing to check if the message is received correctly: 10+3E+FE = 14C, 14C & FF = 4C = 0x3E = Fault code list, if there’s none then it continues with 0xFE = 0x10 = Request echo, good thing to know to which request the PCM is responding I simply sent the byte 0x10 every second at 7812,5 baud speed. I found out this logic error by trying to connect to the SCI-bus and there were no messages received, only “Frame Errors”.Īfter the fix the first request I tried was the fault codes stored in the PCM: CHRYSLER CCD/SCI SCANNER V1.20 LD Maybe I redesign the PCB if I run out of them. It’s not a major PCB design fault, it works. So the “74LS04” logic converter is not needed, therefore its two input/ouput pins have to be soldered together.
Chrysler drb iii bench test software#
It can also work with the DRB-III ™ Emulator Software to perform most DRB-III diagnostic and reprogramming functions.It turned out that the SCI-bus doesn’t need inverted UART logic to communicate. It must be connected to a laptop using a USB cable. WITECH VCI POD kit connects to a vehicle using the OBD II Cable.
Chrysler drb iii bench test full#
These Features Provide Technicians with Full Dealer-Level Functionality. The wiTECH VCI Pod ™ Using the wiTECH ™ Diagnostic Application, this software is capable of several diagnostic and maintenance This cutting-edge technology will enable technicians to increase their productivity and provide world-class diagnostic services to your customers. It provides the latest significant hardware and software performance enhancements over the StarSCAN ™ And StarMOBILE ™ Diagnostic tools. The wiTECH ™ Diagnostic system is designed to work on Chrysler, Jeep, Dodge, RAM vehicles. After open "wiTech Diagnostic Application" on the desktop, you can't go on operating unless the "Device" status is green.
Chrysler drb iii bench test driver#
After connect the WITECH hardware with the computer, please check whether the driver is well installed, whether the software find the hardware. WITECH software start is a bit slow Please wait until the screen has a full display before proceeding to the next step.Ĥ. When you want to use WITECH software to program, you'd better change the language to English Programming in English will be very stable.ģ. WITECH VCI POD contains DRB III emulator, please connect the vehicle to the WITECH before using DRB III emulator, and it needs one minute to open DRB III emulator.Ģ.
WITECH VCI POD Diagnostic Tool for ChryslerĬhrysler Diagnostic Tool (WITECH VCI POD) is designed to work on Chrysler, Jeep, Dodge, RAM vehicles.Ĭhrysler Diagnostic Tool (WITECH VCI POD) Installation Tipsġ.
0 kommentar(er)
